Bicycle Brake and Gear Cables Explained: Inner Wires, Housing and When to Replace Them (India)
Sluggish shifting and a spongy brake lever are usually cable problems, not component problems. Here is how cables and housing work and what to buy in India.
Bicycle brake and gear cables explained: the cheapest fix for poor shifting
Bicycle brake and gear cables are the least glamorous parts on a bike and the cause of a large share of shifting and braking complaints. A derailleur that hesitates going to smaller cogs, or a brake lever that returns slowly, is far more often a dirty or corroded cable than a worn component. After an Indian monsoon, grit and water inside the housing make things worse. The good news is that new cables cost very little: a basic AGT galvanized brake inner cable is ₹75 on InstaSport. This guide explains the parts, the materials and when to replace them.
Inner cable and outer housing: what is the difference?
A cable system has two parts. The inner cable, or inner wire, is the braided steel wire that the lever pulls. The outer housing is the sleeve it runs through, which gives the wire something to pull against as it goes around bends. Friction between the two is what makes controls feel heavy, so both matter. Small end caps, called ferrules, finish each end of the housing, and a crimped tip stops the inner wire from fraying.
Are brake cables and gear cables the same?
No, and they must not be mixed.
- Brake inner cables are thicker, about 1.5 to 1.6 mm, with a barrel-shaped end for flat-bar levers or a mushroom-shaped end for drop-bar road levers.
- Gear inner cables are thinner, about 1.1 to 1.2 mm, with a small cylindrical end.
- Brake housing is usually 5 mm and spiral-wound so it can withstand high force.
- Gear housing is usually 4 mm with lengthwise strands so it does not compress and shifting stays precise. Never use gear housing for brakes, because it can split under braking load.
Check your lever type before ordering a brake cable.
Galvanized vs stainless vs PTFE-coated cables
| Type | Example | Price | Notes |
|---|---|---|---|
| Galvanized | AGT Gear Inner Cable Basic | ₹89 | Cheapest; fine for dry use but rusts sooner |
| Stainless steel | AGT Gear Inner Cable Stainless Steel | ₹239 | Resists corrosion; the sensible default in India |
| PTFE-coated | AGT Gear Inner Cable PTFE Coated | ₹370 | Lower friction; useful on frames with internal routing |
| PTFE brake cable | AGT Brake Inner Cable Slick Galvanized PTFE (road) | ₹290 | Smoother lever feel on drop-bar bikes |
For a commuter or hybrid ridden year-round, stainless inner cables are worth the small premium. Coated cables feel best when new, but the coating can wear, so they suit riders who service their bikes regularly.
When should you replace bicycle cables?
- Shifting is slow or inconsistent even after adjusting the barrel adjuster, especially when moving to smaller cogs.
- The brake lever feels gritty or does not snap back.
- You can see frayed strands at the clamp bolt or inside the shifter, rust on exposed sections, or cracked and kinked housing.
- As routine maintenance: about once a year for regular riders, and soon after the monsoon for bikes ridden through it.
A frayed brake cable is a safety issue. Replace it before the next ride.
Should you replace the housing too?
Usually yes. A new wire in dirty housing gains little. Replace housing whenever it is kinked, cracked or more than a couple of years old; Yokozuna 4 mm shift housing is ₹400. Complete kits save guesswork: the Ciclovation Advanced Performance universal shift cable set and the Ciclovation Advanced Performance road brake cable set are ₹1,399 each, and the premium Jagwire 2x Elite Sealed shift kit at ₹3,960 adds sealed, lined housing for wet and dusty conditions. Finish every cut end with a tip; a pack of ten Sumart cable tips is ₹100.
DIY or bike shop?
Changing an inner cable on external routing is a manageable home job with Allen keys and a proper cable cutter; ordinary pliers crush the housing and fray the wire. Internally routed frames and integrated road shifters are fiddlier, and brakes must be tested carefully before riding. If in doubt, buy the cables and have a mechanic fit them.
Shop the gear
- AGT Brake Inner Cable Basic Galvanized (Road/MTB) — ₹75
- AGT Gear Inner Cable Basic (SRAM/Shimano) — ₹89
- AGT Gear Inner Cable Stainless Steel — ₹239
- AGT Gear Inner Cable PTFE Coated — ₹370
- Yokozuna 4mm Shift Housing — ₹400
- Ciclovation Advanced Performance Universal Shift Cable Set — ₹1,399
- Jagwire 2x Elite Sealed Shift Kit — ₹3,960
Related reading
- Bicycle Headset Bearings Explained: Sizes, 45/45° Angles and How to Find the Right One (India)
- Matching Your Cassette, Chain and Shifter: A Bicycle Speed Compatibility Guide for India
- Pre-Winter Bicycle Service Checklist for India (2026-27): Chain, Tyres and Brakes
Frequently asked questions
How often should bicycle cables be replaced?
For regular riders, about once a year is a reasonable routine, and sooner if the bike is ridden through the monsoon. Replace immediately if you see fraying, rust or kinked housing.
Can I use a gear cable as a brake cable?
No. Gear cables are thinner and have a different end fitting, and gear housing is not designed for braking forces. Always use brake-specific inner cables and housing for brakes.
Are stainless steel bicycle cables worth it?
Yes for most Indian riders. Stainless cables resist corrosion better than galvanized ones and cost only a little more; an AGT stainless gear inner cable is listed at ₹239 on InstaSport.